Source for standards, engineering specifications, manuals and technical publications

This document specifies a test method to assess the ignitability of mattresses, upholstered bed bases or mattress pads when subjected to a gas flame as an ignition source. This document does not apply to air mattresses and water beds.

This document specifies design principles and performance requirements for sludge treatment and storage facilities at wastewater treatment plants serving more than 50 PT.
NOTE   Other sludges and organic wastes may be treated together with municipal sewage sludge.

This document specifies definitions of and general requirements to a pressure relief valve for limiting internal pressure of dimethyl ether (DME) fuel containers intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles using gaseous fuels in accordance with ISO 16861. It is not applicable to the following: a) fuel containers for any application other than as noted above; b) stationary, ship, railroad vehicle or aircraft DME engine installations; c) fuel container mounting hardware; d) parts of vehicle fuel systems other than the fuel container; e) electronic fuel management; f) refuelling receptacles. NOTE 1 It is recognized that miscellaneous component properties not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 22760 series, including subjecting the component to appropriate functional tests. NOTE 2 All pressures referred to in this document are gauge pressures unless otherwise specified.

This document provides guidance on the collation of the measurements required for the management of siltation at river structures. These include structures used by water supply utilities, other major water abstractors, HEP producers, and for flow measurement by environmental protection agencies.
The document is also intended for use when a redundant structure is being removed, or when modifications to a structure are being made to facilitate fish migration or for river restoration. This is to ensure that the impacts of these changes are adequately monitored and recorded.
The document covers the provision of routine measurements, and the checks and requirements that need to be made by the operator so that specific basic information is collated and made readily available. This information is used to inform decision-making by environment management agencies that authorise flushing, sediment clearance or sedimentation removal. This is to ensure minimal environmental impacts, and to compliance with existing environmental legislation.

This document provides definitions for JPEG application specific markers found in Rec. ITU‑T T.81 | ISO/IEC 10918-1 and Rec. ITU-T T.84 | ISO/IEC 10918-3.

This document specifies definitions of and general requirements to the 85 % stop valve, intended for use on the types of motor vehicles defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles using gaseous fuels in accordance with ISO 16861. It is not applicable to the following: a) fuel containers, except to the extent explicitly referred to in this document; b) stationary, ship, railroad vehicle or aircraft dimethyl ether (DME) engine installations; c) electronic fuel management; d) refuelling receptacles. NOTE 1 It is recognized that miscellaneous component properties not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 22760 series, including subjecting the component to the appropriate functional tests. NOTE 2 All pressures referred to in this document are gauge pressures unless otherwise specified.

This document specifies a test method to assess the ignitability of mattresses, upholstered bed bases or mattress pads when subjected to a smouldering cigarette as an ignition source. This document does not apply to air mattresses and water beds.

This document specifies definitions of and general requirements to a pressure relief device for limiting internal pressure of dimethyl (DME) fuel containers intended for use on the types of motor vehicles as defined in ISO 3833. It also provides general design principles and specifies requirements for instructions and marking. This document is applicable to vehicles using gaseous fuels in accordance with ISO 16861. It is not applicable to the following: a) fuel containers for any application other than as noted above; b) stationary, ship, railroad vehicle or aircraft DME engine installations; c) fuel container mounting hardware; d) electronic fuel management. NOTE 1 It is recognized that miscellaneous component properties not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 20760 series, including subjecting the component to appropriate functional tests. NOTE 2 All pressures referred to in this document are gauge pressures unless otherwise specified.

This document defines terms commonly used in the field of quantum computing. This document is applicable to all types of organizations (e.g. commercial enterprises, government agencies, not-for-profit organizations) to exchange quantum computing concepts.

This document specifies definitions of and general requirements to level indicators, intended for use on the types of motor vehicles defined in ISO 3833. It also provides general design principles, and specifies requirements for instructions and marking. This document is applicable to vehicles using gaseous fuels in accordance with ISO 16861. It is not applicable to the following: a) fuel containers, except to the extent explicitly referred to in this document; b) stationary, ship, railroad vehicle or aircraft dimethyl ether (DME) engine installations; c) electronic fuel management; d) refuelling receptacles. NOTE 1 It is recognized that miscellaneous component properties not specifically addressed herein can be examined for compliance with the criteria of any applicable part of the ISO 22760 series, including subjecting the component to the appropriate functional tests. NOTE 2 All pressures referred to in this document are gauge pressures unless otherwise specified.

This document specifies the technical delivery conditions for corrosion-resistant alloy seamless products for casing, tubing, coupling stock and accessory material (including coupling stock and accessory material from bar) for two product specification levels: PSL-1, which is the basis of this document; PSL-2, which provides additional requirements for a product that is intended to be both corrosion and cracking resistant for the environments and qualification method specified in Annex G and in the ISO 15156 series or NACE MR0175. This document contains no provisions relating to the connection of individual lengths of pipe. Demonstration of conformance to ISO 15156-3:2020 or NACE MR0175-2021 of material affected by end sizing, connection manufacture or welding operations is outside the scope of this document. This document contains provisions relating to marking of tubing and casing after threading. This document is applicable to the following five groups of products: a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure; b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy; c) group 3, which is composed of stainless alloys with an austenitic structure (iron base); d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base); e) group 5, which is composed of bar only (Annex F) in age-hardened (AH) nickel-based alloys with austenitic structure.

This document specifies requirements and gives test methods for physical properties of single-use medical gloves (i.e. surgical gloves and examination/procedure gloves) in order to ensure that they provide and maintain in use an adequate level of protection from cross contamination for both patient and user.
This document does not specify the size of a lot. Attention is drawn to the difficulties that can be associated with the distribution and control of very large lots. The recommended maximum individual lot size for production is 500 000.

This document defines terms that are commonly used in the area of waste collection and transportation
management. It aims to align with terminology used internationally.

This document specifies requirements for rebreather instructor training programmes which provide the competencies required to be able to train rebreather divers.
This document specifies evaluation criteria for these competencies and specifies the requirements for four levels of rebreather instructor.
This document specifies the requirements under which training is provided, in addition to the general requirements for recreational diving service provision in accordance with ISO 24803.

This document specifies requirements for information to be supplied by the
manufacturer on the performance, operation and maintenance of portable suction
equipment designed and constructed to be transported for use in non-permanent
healthcare environments.

This standard provides a procedure to validate a calculation tool of spectrophotometric and thermal characteristics of the glass products following EN 410 or EN 673. It provides also the methodology to correctly use measured data in the calculation tool.  
The following characteristics are included in the scope of this standard:
- light transmittance (tv)
- light reflectance - both sides (rv, r'v)
- solar direct transmittance (te)
- solar direct reflectance – both sides (re, r'e)
- total solar energy transmittance (solar factor or g value) (g)
- thermal transmittance (U value) in the vertical position
The following characteristics are excluded from the scope of this standard:
- UV transmittance (tuv)
- shading coefficient (SC)
- general colour rendering index (Ra)
- thermal transmittance (U value) at angles other than vertical

This document specifies minimum requirements for concentrates used for haemodialysis and related therapies.
This document is addressed to the manufacturer of such concentrates. In several instances in this document, the dialysis fluid is addressed, which is made by the end user, to help clarify the requirements for manufacturing concentrates. Because the manufacturer of the concentrate does not have control over the final dialysis fluid, any reference to dialysis fluid is for clarification and is not a requirement of the manufacturer.
This document includes concentrates in both liquid and powder forms. It also includes additives, also called spikes, which are chemicals that can be added to the concentrate to supplement or increase the concentration of one or more of the existing ions in the concentrate and thus in the final dialysis fluid.
This document also specifies requirements for equipment used to mix acid and bicarbonate powders into concentrate at the user's facility.
Concentrates prepared from pre-packaged salts and water at a dialysis facility for use in that facility are excluded from the scope of this document. Although references to dialysis fluid appear herein, this document does not address dialysis fluid as made by the end user. This document also excludes requirements for the surveillance frequency of water purity used for the making of dialysis fluid by the dialysis facility. This document does not address bags of sterile dialysis fluid or sorbent dialysis fluid regeneration systems that regenerate and recirculate small volumes of the dialysis fluid.
This document does not cover the dialysis fluid that is used to clinically dialyse patients. Dialysis fluid is covered in ISO 23500-5. The making of dialysis fluid involves the proportioning of concentrate and water at the bedside or in a central dialysis fluid delivery system. Although the label requirements for dialysis fluid are placed on the labelling of the concentrate, it is the user's responsibility to ensure proper use.
This document does not cover haemodialysis equipment, which is addressed in IEC 60601-2-16:2012.

This International standard method specifies a procedure for the determination of saturated and aromatic hydrocarbons (from C10 to C50) in vegetable fats and oils using the online-coupled HPLC-GC-FID. This standard is not intended to be applied to other matrices.
The method can be used for the analysis of mineral oil saturated hydrocarbons (MOSH) and/or mineral oil aromatic hydrocarbons (MOAH).
According to the results of the interlaboratory studies, the method has been proven suitable for MOSH mass concentrations above 3 mg/kg and MOAH mass concentrations above 2 mg/kg.
In case of suspected interferences, the fossil origin of the MOSH and MOAH fraction can be verified by examination by GC⨯GC-MS.
An alternative method for the epoxidation of the MOAH fraction (performic acid epoxidation) is proposed in Annex C. This alternative method provides comparable results to the ethanolic epoxidation of the MOAH fraction described in 8.5. This alternative method for epoxidation has proven to be efficient for samples with a high amount of interferences in the MOAH fraction (e.g. tropical oils).